Features
Security Features
Security Code
1. To access functions beginning with 8, press FCN 8.
2. Enter the security function:
1 Call Restriction
2 Unlock Code
3 Status Monitor
4 PIN Number Programming
5 Automatic PIN Number Enable
3. Enter the 4-digit Security Code. If you enter a wrong code, Code Error displays.
NOTE: The Security Code is pre-programmed You cannot change the Security Code.
Call Restriction
1. Press FCN 81 while in Standby, then enter the 4-digit Security Code. Current Call Restriction status displays.
2. Press j / # to change the Call Restriction level. Select from the following levels:
No Restriction All call features are enabled.
Local Only Disables long distance calls. Only 7-digit local calls and toll-free calls allowed.
Recall 1-19 Disables numbers not stored in memory locations 1-19. Also prevents entry of new phone numbers into memory locations.
Receive Only Disables all calls except for emergency calls.
3. Press END to save your selection and exit this mode.
Call Restriction Interaction
• 911 calls are always available.
• Manual DTMF is only available during No Restriction and Local Only.
• Dial Tone Dialing is unavailable during Recall 1-19 and Receive Only.
Creating an Unlock Code
1. Press FCN 82, then enter the Security Code. The current Unlock Code displays.
2. To create a new Unlock Code, enter 3 digits for the new code. If you make a mistake, or if you do not want to use the new Unlock Code, press CLR to use the original code. Press CLR again to exit this mode.
If you did not make any changes, press CLR to exit this mode.
3. Press END to save the new code and exit this mode.
NOTE: You can program a new Unlock Code even while the phone is locked.
Status Monitor
1. Press FCN 83, and enter the Security Code. Status (ON or OFF) displays.
2. Press j / # to enable or disable the Status Monitor.
3. Press END to save your setting and return to Standby.
Status Monitor Messages
Status Monitor Messages display in the following formats:
Conversation Mode
| Message... |
Description... |
|
CCCC |
Voice channel or control channel in Standby |
|
RRR |
Received RSSI |
| A |
Serving system support level for authentication |
| XXXXX | Received SID |
| P |
Transmit power level 0-7 |
| S | Received SAT frequency
0=5970 Hz, 1=6000 Hz, 2=6030 Hz, 3=no SAT |
PIN Number Programming
If your service provider supports this feature, a PIN must be sent whenever you make a call. Rather than entering it each time, you can program the phone to send the PIN automatically.
1. Press FCN 84, followed by your Security Code. The current PIN displays. If there is no current PIN, a line of dashes displays.
2. To change the PIN, enter the desired 4-digit PIN. If you make a mistake, or if you do not want to use the new PIN, press CLR to use the original PIN. Press CLR again to exit this mode.
If you did not make any changes, press CLR to exit this mode.
3. Press END to save the new PIN and return to Standby mode.
Enabling Automatic PIN
With Automatic PIN enabled, the phone sends the PIN automatically when required by the cellular system.
1. Press FCN 85 followed by the Security Code. The status of the PIN (ON or OFF) displays. If there is no PIN programmed, No Pin displays.
2. Press j / # to enable or disable Automatic PIN.
3. Press END to save the setting and return to Standby mode.
Locking the Phone
1. Press FCN 5 while in Standby mode. Loc Code displays.
2. Enter the 3-digit Unlock Code. Loc'd displays, indicating the phone is locked. If you enter a wrong Unlock Code, Code Error displays.
NOTE: You can dial 911 while the phone is locked. DO NOT use 911 as your Unlock Code.
Timers
Last Talk Time
Last Talk Time displays the total time for the most recent call.
1. Press FCN 6 while in Standby. MM-SS displays.
MM is the total minutes
SS is the total seconds
2. Press END to return to Standby mode.
Operating Timer
Operating Timer displays the total time for all calls. This time cannot be reset.
1. Press FCN 7 while in Standby. HHH-MM displays.
HHH is the total hours
MM is the total minutes
2. Press END to return to Standby mode.
Keypad Lock
Press END and s simultaneously to enable. button Loc displays and all keys (including PWR) are disabled to prevent accidental key presses. Press END and t simultaneously to disable. Keypad lock turns off automatically when you receive a call.
Automatic Answer
Answers calls if you do not within 10 seconds.
1. Press FCN 4 while in Standby.
2. Press j / # to enable or disable Automatic Answer.
3. Press END to save your setting and return to Standby mode.
NOTE: Automatic Answer is disabled when the Keypad Lock is enabled.
Call-In-Absence Indicator
When you receive a call, and are unable to answer it, the message Called displays. If your service provider supports Caller ID service and you subscribe to it, the caller's number displays on the top line of your phone's display.
Network Service Features
If your service provider supports these features and you subscribe to them, your phone displays Caller ID and Message Waiting information.
Caller ID
When you receive a call, the caller's number displays on the top line of your phone's display. Answer the call as you would normally.
If you do not answer the call, your phone displays the Caller ID information and Called until you press END or CLR. After pressing END or CLR, you can return the call by pressing TALK.
If you have Call Waiting, the system may display Caller ID information when another call comes in. You can press TALK to switch between the two calls, or press CLR to ignore the other call and exit the Caller ID display.
Message Waiting
When you have unchecked voice mail your phone displays the Message Waiting icon. This icon displays until you listen to all of your messages.
System A/B Selection
1. Press FCN 3. The current System A/B setting displays.
2. Press j / # to change the setting to one of the following:
Prefer A Phone scans System A first when it is scanning.
Prefer B Phone scans System B first when it is scanning.
Home Only Phone does not roam.
Only A Phone scans only System A when it is scanning.
Only B Phone scans only System B when it is scanning.
3. Press END to accept and save the displayed setting and return to Standby.
NOTE: If Roam Inhibit is enabled in NAM, the System A/B Select function is not available and Roam Inhibit displays. Press END.