Commonly Used Features

Special Dialing Features

One Touch Dialing

To dial the One Touch Dial number, press P for at least 1 second.

NOTE: If the number is more than 12 digits long, press the RCL key to view the first digits. If there is no One Touch number programmed, Empty displays.

Super Speed Dialing

Dial any number stored in memory locations 1-09 by entering the one digit memory address (1-9) and pressing TALK.

Speed Dialing

1. Enter a memory address number from 01-99.

2. Press TALK. The number displays as the phone dials. Refer to Storing for information on assigning numbers to memory locations.

Last Number Redial

Use Last Number Redial to display and dial any of the last 3 numbers dialed. To dial the last number dialed press TALK. To choose from the last 3 numbers, do the following:

1. Press RCL twice (while in Standby) to access the last 3 numbers dialed. The most recently dialed number displays. If none exists, Empty displays.

NOTE: Only the last 12 digits of the number display. To view earlier digits press RCL.

2. Use s and t to scroll through the last 3 numbers dialed.

3. Press TALK to dial the displayed phone number.

NOTE: You can add digits to the displayed phone number.

Automatic Redial

Automatic Redial redials a number when the phone is unable to connect to the cellular system. If the call does not connect after 10 tries, a Reorder tone sounds and you must dial again.

1. Press FCN 21 while in Standby. Auto Redial (ON or OFF) displays.

2. Press TALK to enable or disable this feature.

3. Press END to save the displayed setting and return to Standby.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Using Call Mute Function

During conversation, press FCN for more than 1 second to turn your phone’s microphone off and put a call on hold. MUTE displays. Press any key to return to the conversation.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Changing Volume Controls

Adjusting the Ringer Volume

1. Press FCN 41 while in Standby. Current volume displays.

2. Use # and * to adjust volume up and down. Adjust ringer volume from 0 (off) to 7.

3. Press END to complete your setting and return to Standby.

Adjusting the Speaker Volume

Use the Speaker Volume function to adjust the dial tone, Reorder, and Intercept tones.

1. Press FCN 42. Speaker Vol. and the current volume display.

2. Use # and * to adjust speaker volume up and down from 1 to 7.

3. Press END to complete your setting.

Adjusting the Conversation Volume

In conversation, use s and t to adjust volume up and down from 1 to 7.

Adjusting the Key Tone Volume

In Standby, use s and t to adjust volume up and down from 0 (off) to 7.

NOTE: This function also sets Error, Retry Call Success, Low Battery Alarm (min = 1), Wake-up, and Power Off tone levels.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Adjusting the Display Contrast

1. While in Standby, press FCN 24.

2. Use TALK and END to adjust the display contrast.

3. Press P to complete your setting and return to Standby.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Displaying Your Phone Number

1. Press FCN 11. The screen displays your phone number.

2. Press END to return to Standby.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Sending DTMF Tones

You can store and transmit Dual Tone Multi-Frequency (DTMF) tones—the sounds created when you press the keys on your phone’s keypad. It is sometimes necessary to send DTMF tones while communicating with computerized answering systems.

Automatic DTMF

To enter a string of DTMF tones to send after you dial a phone number, do the following:

1. Enter the desired phone number.

2. Press FCN, then press 0 to program a pause.

3. Enter the DTMF string on the keypad.

4. Repeat steps 2 and 3 as necessary to add additional DTMF strings.

5. Press TALK to dial the phone number.

6. After the call connects, press TALK for each DTMF string you want to send.

 

Storing DTMF Strings

Store DTMF strings the same way you store phone numbers. You can recall these DTMF strings whenever you need to send them. See Storing on the next page.

Recalling DTMF Strings from Memory

1. Enter the telephone number of the party you wish to call.

2. Press FCN, then press RCL. An M appears after the phone number as a separating mark.

3. Enter the memory address of the DTMF string you want to send.

4. If necessary, repeat steps 2 and 3 to add another number to be sent.

5. Press TALK to dial the phone number. After the call connects, press TALK once for each DTMF string.